edytlab
Audio Tools Reference

Effects

Equalizer, compressor, reverb, filters and other effects you can apply to a track.

On this page17 tools
eq

EQ a track with biquad bands. Each band: freq_hz, gain_db, optional Q (default 1.0; 0.707 for shelves), optional type peak (default), low_shelf or high_shelf.

Example prompt: boost the highs on track 1 by 3 dB at 8 kHz

Returns: node_id

compressor

Apply a dynamic compressor with configurable threshold, ratio, attack, and release. Uses an envelope follower for smooth gain reduction.

Example prompt: compress track 1: threshold -18 dB, ratio 4:1

Returns: node_id

noise_reduction

Remove broadband noise via spectral subtraction (realFFT + overlap-add). Estimates the noise floor from the first noise_duration_sec seconds, or from any range (noise_from / noise_to, optionally on another track with noise_track), and subtracts it from the signal.

Example prompt: reduce background noise on track 1

Returns: node_id

reverb

Apply Freeverb algorithmic reverb. room_size (0-1) controls reverb length, damping (0-1) controls high-freq decay, wet (0-1) is the wet/dry blend.

Example prompt: add a small room reverb

Returns: node_id

echo

Echo: delay_ms + decay (0..1), or taps [[delay_ms, gain], ...] with feedback (0..0.65).

Example prompt: add a 300 ms echo

Returns: node_id

phaser

Apply a phaser effect using an all-pass filter chain with LFO sweep. rate_hz controls LFO speed; depth is the wet blend; stages sets the filter chain length (2-12).

Example prompt: add a slow phaser

Returns: node_id

wah_wah

Sweep a band-pass filter around a base frequency, with adjustable rate, depth and resonance.

Example prompt: add a slow wah-wah effect

Returns: node_id

tremolo

Apply tremolo (LFO amplitude modulation). rate_hz controls oscillation speed; depth (0..1) controls modulation depth.

Example prompt: add tremolo at 5 Hz

Returns: node_id

distortion

Apply soft-clip distortion (tanh waveshaper) followed by a tone filter. drive > 1 increases gain before clipping; tone (0=dark, 1=bright) controls the output filter.

Example prompt: drive track 2 a little

Returns: node_id

stereo_widener

Widen or narrow the stereo field using M/S processing. width=0 collapses to mono, width=1 is original, width=2 doubles the stereo width. Requires stereo track.

Example prompt: widen the stereo image

Returns: node_id

vocal_reduction

Reduce center-panned vocals using L-R channel subtraction (Karaoke effect). Works on stereo tracks; results depend on how centrally the vocals are mixed.

Example prompt: take the vocals out

Returns: node_id

declip

Reconstruct clipped peaks using cubic interpolation. threshold_dbfs sets the clipping level (default -0.01 dBFS). Reports runs found and repaired per channel; runs without clean edges are left alone. Restored peaks above full scale apply a shared gain (reported as gain_db) to avoid re-clipping. Unclipped audio stays byte-identical and retains its node; repaired audio appends a new node.

Example prompt: repair the peaks clipped at minus 3 dBFS on track 0

Returns: node_id, runs_found, runs_repaired, gain_db

repair_span

Interpolate a damaged span up to 100 ms with bidirectional tonal prediction, falling back to bounded cubic interpolation. start_sec and end_sec are session seconds; two clean samples are needed on each side. Preserves duration and channels. Appends a new node.

Example prompt: repair the damaged span from 2.1 to 2.12 seconds on track 0

Returns: node_id

click_removal

Remove clicks and pops by detecting sample spikes (via median filter) and replacing them with interpolated values. threshold is the amplitude deviation that triggers detection.

Example prompt: remove the clicks

Returns: node_id

low_pass_filter

Apply a Butterworth low-pass filter to a track, removing frequencies above cutoff_hz.

Example prompt: roll off everything above 8 kHz

Returns: node_id

high_pass_filter

Apply a Butterworth high-pass filter to a track, removing frequencies below cutoff_hz.

Example prompt: high-pass at 80 Hz

Returns: node_id

notch_filter

Apply a notch (band-reject) filter to a track, attenuating frequencies near center_hz. q controls the width: higher Q = narrower notch.

Example prompt: notch out the 50 Hz hum

Returns: node_id